QNAP的transmission安装

fttbcm

我的settings.json配置如下，也是不能运行，输入http://IP:9091出现：
403: Forbidden
Unauthorized IP Address.

Either disable the IP address whitelist or add your address to it.

If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.

If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.
明显就是IP地址认证不能通过，但我觉得没有输错呀，有谁能帮帮我，我的settings.json配置如下：
{
    "alt-speed-down": 50,
    "alt-speed-enabled": false,
    "alt-speed-time-begin": 540,
    "alt-speed-time-day": 127,
    "alt-speed-time-enabled": false,
    "alt-speed-time-end": 1020,
    "alt-speed-up": 50,
    "bind-address-ipv4": "0.0.0.0",
    "bind-address-ipv6": "::",
    "blocklist-enabled": false,
    "dht-enabled": true,
    "download-dir": "\/share\/Qdownload\/transmission\/",
    "encryption": 0,
    "lazy-bitfield-enabled": true,
    "message-level": 2,
    "open-file-limit": 32,
    "peer-limit-global": 240,
    "peer-limit-per-torrent": 60,
    "peer-port": 51413,
    "peer-port-random-high": 65535,
    "peer-port-random-low": 49152,
    "peer-port-random-on-start": false,
    "peer-socket-tos": 0,
    "pex-enabled": true,
    "port-forwarding-enabled": true,
    "preallocation": 1,
    "proxy": "",
    "proxy-auth-enabled": false,
    "proxy-auth-password": "",
    "proxy-auth-username": "",
    "proxy-enabled": false,
    "proxy-port": 80,
    "proxy-type": 0,
    "ratio-limit": 2.0000,
    "ratio-limit-enabled": false,
    "rpc-authentication-required": false,
    "rpc-bind-address": "0.0.0.0",
    "rpc-enabled": true,
    "rpc-password": "",
    "rpc-port": 9091,
    "rpc-username": "",
    "rpc-whitelist": "*.*.*.*",
    "rpc-whitelist-enabled": true,
    "speed-limit-down": 100,
    "speed-limit-down-enabled": false,
    "speed-limit-up": 100,
    "speed-limit-up-enabled": false,
    "umask": 18,
    "upload-slots-per-torrent": 14

fttbcm

哈哈终于明白了，我是看这个看懂的http://www.hkepc.com/forum/viewt ... 5086&extra=&page=33
具体说来说是在执行share/HDA_DATA/.qpkg/Optware/bin/目录下去启动Transmission时,执行下列操作：(这步很重要)
transmission-daemon -p 9091 -f -T -a *.*.*.* -w /share/HDA_DATA/Qdownload/ -g /share/HDA_DATA/Qdownload/config/
这样就行了。具体请看我的BBS:http://hd2pt.com/viewthread.php?tid=37&extra=page%3D1

                               
登录/注册后可看大图

p_abing

我的无法保存AUTORUN.SH，一输入WQ命令，老提示：ERROR 5 INPUT/OUTPUT。

rnir

前面的操作呢，没mount好flash吧

p_abing

mount -t ext2 /dev/mtdblock5 /tmp/config
这样的命令对吧？

p_abing

autorun.sh内容：
#!/bin/sh
#Transmission start
echo "/share/HDA_DATA/.qpkg/Optware/lib/" >> /etc/ld.so.conf
ldconfig
export EVENT_NOEPOLL=0
export TRANSMISSION_WEB_HOME=/share/HDA_DATA/.qpkg/Optware/share/transmission/web
/share/HDA_DATA/.qpkg/Optware/bin/transmission-daemon -g /share/HDA_DATA/Qdownload/config/ > /share/HDA_DATA/Qdownload/debug_tm.txt
#Ctrl+O WriteOut
chmod +x /tmp/config/autorun.sh
# And finally umount
umount /tmp/config

始终无法保存！不知道什么问题。出现23楼图片中的错误提示。

p_abing

前面的操作呢，没mount好flash吧
rnir 发表于 2010-3-10 07:59

                               
登录/注册后可看大图

看来ERROR 5 INPUT/OUTPUT确实是mount的问题。
但是我已经按http://wiki.qnap.com/wiki/Running_Your_Own_Application_at_Startup
的说明：
TS-109, TS-109P, TS-119, TS-209, TS-209P, TS-219, TS-409 (Marvell ARM), TS-419P: Mount the config ramblock /dev/mtdblock5:
# mount -t ext2 /dev/mtdblock5 /tmp/config来加载FLASH了啊。问题到底出在什么地方？

rnir

注意#不是命令的一部分

p_abing

#是注释，不影响vi的保存。我估计是mount的问题。

rnir

当然也可能那个方法不适用最新版本的固件，你可以到官方论坛上去转转

p_abing

固件是3.2.3的。可能是固件问题。官网上问了，但是说我是vi命令的问题，我试了，命令肯定没问题，看来还是固件的问题可能性大。

p_abing

解决了，见：http://nas1.cn/thread-2710-1-1.html

人在旅途

mark..............

从头再来

ding  ding  ding  ...  zou  ren  lo .na ji fen

玻璃瓶

11111dsfsdfsdfsdfdssfsdfsff

uif0415

嗯，端口映射很重要

hehhui

请问，系统的qpkg transmission好用吗？